Connect with us

Concrete

Valme to exhibit pumping systems at World of Concrete 2020

European manufacturer Valme is unveiling a branch in Wisconsin and a range of concrete distribution

Republished by Plato

Published

on

European manufacturer Valme is unveiling a branch in Wisconsin and a range of concrete distribution pumping systems for World of Concrete 2020 in Las Vegas. 

Valme is to exhibit two gate valves with blades made from especially wear resistant materials as well as a fully dismantlable 1.5” and 2” shotcrete nozzle (DN38 and DN50 respectively).  In addition, Valme North America will unveil its line of DN125 double-layer LLN 2.5+2, LLT 3+1.5 and LLH 5+3 pipes and DN125 reinforced chromium carbide bends in 7 and 12mm thicknesses.

Other products on display will include standard and double-layer pipes, chrome carbide elbows and rubber hoses as well as HD couplings, collars and gaskets.

Eric Zimmermann, general manager of Valme North America, says: “ We offer specialist expertise, a wide range of products and services and the ability to meet the full spectrum of market requirements relating to concrete pumping equipment and pumping systems.”

World of Concrete 2020 is taking place from the 4-7 February at the Las Vegas Convention Center.

(Visited 93 times, 1 visits today)

Source: https://www.aggregateresearch.com/news/valme-to-exhibit-pumping-systems-at-world-of-concrete-2020/

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.



how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.





how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.





how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading
CBD4 days ago

CBD News: CBD court ruling brings additional support in Germany for access

Material1 day ago

Improved sinter-bonding properties of silver-coated copper flake paste in air by the addition of sub-micrometer silver-coated copper particles

Heartland3 days ago

Everything You Need to Know About the Miraculous Health Benefits of Cannabidiol

CBD4 days ago

GreenheartCBD Founder Paul Walsh named to the All-Ireland Business All Star List

Material5 days ago

Fabrication and characterization of nanostructured zinc oxide on printed microcontact electrode for piezoelectric applications

Material5 days ago

Gamma radiation modified the optical, electrical, and antibacterial characterization of CuONPs doped in Polyethylene Oxide/Polyvinyl Alcohol

Heartland5 days ago

Hemp Pain — Crop falling out of favor with growers

Heartland5 days ago

Hemp Biomass Decarboxylation Service Market 2020 Share, Vendor Detail, Technologies …

Heartland5 days ago

3 Delta-8 THC Flowers You Must Try This Black Friday

Uncategorized5 days ago

Aurora Cannabis Announces Israeli Medical Supply Agreement with Cantek

Material2 days ago

Colorful and antibacterial nylon fabric via in-situ biosynthesis of chitosan mediated nanosilver

Heartland8 hours ago

High CBD/low THC content for a new user?

Heartland5 days ago

COA | CBD Certificate of analysis

Material2 days ago

Synthesis of Silica-based Scaffolds with High Porosity and Controllable Microstructure by a Sintering-free Sol-gel/Freeze-casting Hybrid Method under Mild Conditions

Heartland5 days ago

Global Hemp Seeds Market 2020 : Industry Analysis by Top Countries Data Definition, Size, Share …

Heartland5 days ago

Vireo Health Q3 Revenue Increases 11% Sequentially to $11.9 Million

Material4 days ago

A comparative study of hot ductility of unadded and Ce-added SA508-4N RPV steels

Heartland2 days ago

Model Katiana Kay Launches Bay Smokes

Heartland1 day ago

What happens when you green out?

Heartland5 days ago

Heartland5 days ago

Oil vs gel caps

CBD4 days ago

The 20 Strongest CBD Oil Products Available

Heartland4 days ago

Cannabidiol Derivative May Be Effective as EB Treatment, Studies Suggest

Concrete2 days ago

Nov 27, DIY Epoxy Concrete Crack Repair – What I use – How I Repair Concrete

Heartland1 day ago

Heartland1 day ago

Anyone try kokonuggz with THC?

Heartland5 days ago

Heartland5 days ago

Heartland5 days ago

Heartland5 days ago

Trending

A Cloud Nine Capital Entity Copyright © 2020 – All Rights Reserved Proudly Made in America