Connect with us

Concrete

Dec 7, How To Finish Concrete Smooth By Using A Steel Trowel – Tips & Tricks

This page will show you how to finish concrete smooth by using a steel trowel and mag float. I’ll also have a video showing you how to finish concrete smooth.

Republished by Plato

Published

on

One of the best ways you can learn how to finish concrete smooth is by watching me using a steel trowel to finish this small concrete floor.






I’ve been using a mag float and a steel hand trowel to finish concrete smooth for many years.

There’s a technique I use when I finish concrete that makes using a mag float and hand trowel a little easier to learn.

Keep in mind, timing is everything when finishing concrete. Starting too soon or too late greatly impacts the final results.

These three videos will help you understand the timing of when to start and the process of troweling concrete smooth.

I’ll explain the basics here, then I’ll go into a little more detail:

  1. Mag float the concrete first by moving the mag in a back and forth action while applying moderate downward pressure.
  2. After floating the concrete, let it dry for a bit and then steel trowel it.
  3. Slightly tip up one edge of the steel trowel and while pressing downwards on the trowel, move the trowel in the direction of the edge you have tipped upwards.
  4. Make a sweeping motion while troweling, when you move the trowel in the opposite direction, tip the other edge slightly up so that edge doesn’t dig into the concrete.
  5. Continue moving the trowel back and forth over the surface of the concrete until you see it smooth out the surface.
  6. Once you’ve troweled the entire surface, let it dry a bit and repeat this process as many times as necessary to smooth the surface to your desired look.

The basic tools you’ll need to hand trowel your concrete smooth are:

In the video below, I go into great detail explaining to you how to finish a concrete floor smooth using just a mag float and steel trowel.

Knowing when to start troweling is always the hardest part of the process for most people.

My guidelines for when to start mag floating and troweling are:

  • Check the firmness of the concrete by pressing into it with your fingers
  • If you can press into the surface 1/2 inch or more, then wait 15 – 30 minutes, then check it again.
  • If you can only press into the surface about 1/4 inch, then the surface is ready to mag float.
  • Always mag float the surface first before troweling.
  • If you steel trowel the concrete too early, you could potentially damage the surface by trapping moisture or air under it – this causes blisters and scaling eventually.
  • After you’ve mag floated the surface, you may have to let the concrete dry a bit, then you can steel trowel it.

Below is a really good video that teaches you when to start the finishing process of mag floating.

These three videos and my explanation should help you understand how to finish concrete smooth using a hand trowel.

There’s a lot of variables involved when it comes to when you start the process, like:

  • how wet or dry you poured the concrete (slump)
  • how hot or cold the air temperature is
  • if your project is in the sun or shade
  • what psi concrete mix you use
  • if you use an accelerator or retarder in the mix
  • if the mix has hot or cold water in it
  • the type of sub-base you’re pouring on

If you pour your concrete really wet (or loose) this will greatly extend the amount of time you have to wait to start finishing.

You’ll have to wait for almost all that mixing water to evaporate before the concrete will be firm enough to mag float. 

Not to mention, pouring the concrete too wet will weaken the strength of the concrete also.

What’s the difference between a mag float and a steel trowel?

How to finish concrete smooth by handSteel Trowel on Left – Mag Float on Right

A mag float (the one on the right) is used when the concrete is first poured to smooth the edges and make wet pads for screeding the concrete.

It is also used for the first pass to smooth the concrete when starting the finishing process.

The mag float helps smooth out concrete when it is softer, it brings a finer cream or paste to the surface and prepares the surface for hand troweling.

The steel trowel (on the left) is used for the 2nd, 3rd, 4th, and final finishing passes. (however many it takes to get your desired result).

There are rounded edge trowels like the one above an square edged ones. Both are good, it’s only a preference as to which one you like to use.

When using either the mag float or the steel trowel you have to slightly tip up the edge of the tool in the direction you’re moving it.

You also have to exert some downward pressure on each tool to get a smooth result. The amount of downward pressure will be directly related to how soft or hard the concrete is at that time.

After pouring, screeding, and bull floating the concrete there is usually always some bleed water that rises to the surface of the concrete.

Make sure you let this bleed water evaporate before you start mag floating the surface. Floating the bleed water back into the concrete will weaken the surface and may cause scaling or blistering at a later date.

I always mag float the concrete before steel troweling. Mag floating the surface will continue to let the surface “breath” and continue to let moisture escape out the surface.

If you steel trowel the surface too early, you risk “sealing” off the surface and trapping some moisture that is still trying to rise and evaporate out of the concrete.

This trapped moisture is the cause of scaling, blistering, and a weaker wear surface on concrete floors and slabs.

How to Mag Float concrete

In the picture above I’m mag floating the surface after waiting for the bleed water to evaporate but still when the concrete is soft enough to smooth it out and work up a nice cream on the surface.

In the picture below I’m hand troweling the surface after I’ve mag floated it and let the concrete set up (dry out) a while. 

Each time you hand trowel the surface and let is dry up a bit, it gets smoother. The amount of time in between troweling is what the videos above will help you with.

NOTE: See how I”m tipping up the trowel as I’m moving it to the left. The angle you have to tip up the trowel will vary depending on how hard the surface is.

How to finish concrete smooth with a hand trowel

In Conclusion: Finishing concrete smooth by hand just takes some practice and an understanding of the timing of when to start and how long to let the concrete set in between passes.

It’s a skill that requires just doing it over and over again. Watch and learn from the videos. I give you a lot of tips and details about how to finish concrete, then I show you how to do it.

Subscribe to my YouTube channel to learn a lot more concrete finishing tips and techniques.

Back to How To Finish Concrete

Back to Home Page




If you liked this, please share.  Thanks!




Source: https://www.everything-about-concrete.com/how-to-finish-concrete-smooth.html

Concrete

Why Does Concrete Crack?

One of the biggest hesitations people have when it comes to choosing concrete for their projects is that it cracks over time. While this practical, durable material is one of the strongest goods on the market, the forces of time and nature will eventually cause it to crack–especially if it’s been installed by a non-reputable
Read more

The post Why Does Concrete Crack? appeared first on Port Aggregates.

Republished by Plato

Published

on

One of the biggest hesitations people have when it comes to choosing concrete for their projects is that it cracks over time.

While this practical, durable material is one of the strongest goods on the market, the forces of time and nature will eventually cause it to crack–especially if it’s been installed by a non-reputable company.

But why does concrete crack, and is there anything that will prevent this from happening?

These 5 mistakes are some of the most common causes of concrete cracks.

1. The concrete dried too fast

Faster is not always better. If your concrete mix doesn’t have enough water in it, it will dry too quickly and crack prematurely. Depending on the project, it should take at least a few weeks, maybe even a month, to dry completely.

2. Your contractor put too much water in the mix

Poorly mixed concrete can create a range of problems. Just like having too little water in the mix can cause it to crack, so can having too much water. Water must combine with the concrete at just the right pace so that it can cure and set properly. 

3. Control joints weren’t used

Your concrete must be able to properly expand and contract in different temperatures, otherwise it’ll crack. Control joints are made specifically to help your concrete move about without breaking. 

If your contractor doesn’t use these joints, there won’t be extra room for the slab to adjust its size with the changing temperatures, and it will end up cracking due to its internalized pressure.

4. It was too cold when your concrete was poured

Just like the amount of water affects concrete’s hydration process, so does cold weather. When the temperature drops too low, concrete won’t be able to cure correctly. In these situations, the pour will either need to be postponed, or the subsurface will need to be warmed before pouring. 

5. Your concrete is too thin

Concrete that’s too thin is extremely susceptible to cracking. The proper thickness of your concrete will vary based on its purpose. For example, a driveway that’s meant to support vehicles needs to be thicker than a sidewalk that is not.

Improper concrete thickness is one of the top reasons why DIY concrete projects fail. When taking on a massive project like this on your own, it’s easy to miscalculate the weight your concrete will be expected to bear and the subsequent thickness necessary. Unfortunately, this will result in severe premature cracking.

At Port Aggregates, our contractors have 40 years’ worth of experience built into their pours. Our beautiful concrete has been trusted for decades with good reason. When you hire our professionals, you can say goodbye to premature cracking and rest assured that your slab has been installed properly. Contact us today to request a quote!

Source: https://www.portaggregates.com/why-does-concrete-crack/

Continue Reading

Concrete

Jan 2, How To Form and Pour A Concrete Slab – The #1 Resource on The Web

Learn how to form and pour a concrete slab. My step by step guide will teach you everything you need to know from forming to pouring to finishing.

Republished by Plato

Published

on

how to pour concrete
how to pour a concrete slab

The tools and materials you need to form and pour a concrete slab

MATERIALS:

  • Ready-mix concrete (yardage will depend on size of slab)
  • Wire mesh or Rebar reinforcement
  • Anchor bolts

If your concrete slab is smaller, you can use bags of concrete instead or ready-mix.

Find out how many bags of concrete it takes to make a yard. I did all the calculations for you.

On my Tools Page you can find all the tools required to form and pour concrete.

I also have a concrete yardage calculator that shows you how many yards you need and how many bags of concrete you’ll need.

tools used to form and pour a concrete slab






step by step: how to pour a concrete pad

These are the basic steps I use form and pour concrete slabs. 

I also have a step by step video course with multiple training videos that teaches you all you need to know about how to install your own concrete slab: My Concrete Slab Course

step 1. prepare the area for concrete

how to pour concrete slab prep

Under your concrete slab there should be a compacted base of gravel. You can also use road base, crushed rock, or sand, as long as it’s well compacted.

You’ll probably have to remove some of the existing soil like in the picture above. We removed about 12 inches of the existing sod & loam and replaced it with 8″ of 3/4″ crushed gravel.

This area had a slight slope, so we had to remove more soil on one side than the other to get a level pad.

After installing the gravel, we raked it level (using my laser level) and ran a vibratory compactor over it to settle it and pack it very hard.

NOTE: You may need a permit to install a slab. Contact your local building code officer to see what they require for building a slab. You may also have to keep it a certain distance away from your property line.

PRO TIP: If you have a lot of soil to remove, you can rent a skid steer to do it much easier or hire an excavation contractor to prep the area for you.

BE SAFE: Some states require you to call Dig Safe (811) to check for any underground wires or utilities before you start digging. It’s state law. It’s a free service so be safe.

step 2. building the forms for a concrete slab

Lay out your forms. It’s better to have forms that are a little longer than the size of your slab.

Set up your leveling device. I’m using a self-leveling laser. You can use a 4′ level or a transit level. All 3 will get the job done.

My slab size is 14′ x 10′.

Starting on one side, measure the length of your slab and mark it on the form. (my mark was at 14′ on this side)

Mark each side the same way. (my next side was 10′)

You’ll use these marks to screw the forms together in the next step.

how to pour concrete slab
how to form a concrete slab

step 3. screw the forms together and square the slab

Use your marks to screw the forms together.

Align the inside of the form with your pencil mark. 

You can use a drill driver and deck screws like we do or you can use a hammer and nails to fasten the forms together.

I personally like to use screws, there’s less movement to the forms because you’re not banging on them with a hammer.

Screws are also easier to take out when you go to remove the forms.

After the forms are fastened together it’s time to square the slab.

I measure diagonally each way and slide the forms a little one way or the other until I get the exact same measurement for both diagonal measurements.

It usually takes a few times going back and forth checking until you get it exact.

When you have the slab square, you’re ready to stake it in place.

step 4. stake the forms and set them to grade

Use wooden stakes (or metal pins like me) to secure the forms in place. 

I like to stake each corner, about 8 – 12 inches from the corner, on both sides.

After my 4 corners are staked, I hammer in a stake about every 4′ on all the sides.

To make sure the forms are straight, I use a string line on top of the forms to check them as I stake the forms in place.

After pounding in all the stakes, I use my laser level to set all the forms perfectly level.

The receiver on my grade stick has a solid sounding “beep” when the form is at the pre-determined height. (5″ above my dirt grade)

Screw the form to the stake when it’s at the level you want.

Repeat for all 4 corners, then do the rest of the stakes and your forms will be level.

step 5. add the reinforcement 

wire mesh for a concrete slab

It’s time to install the reinforcement, I’m using wire mesh for this slab. The best way to cut wire mesh is with a pair of bolt cutters.

I buy the flat sheets of mesh, they measure 5′ x 10′. Some local lumber companies stock the flat wire. If not, they usually have the rolls of mesh (5′ x 150′ get these at HD and Lowe’s also)

Another good reinforcement to use for concrete slabs is 3/8 (#3) rebar or 1/2″ (#4) rebar. Rebar comes in 10′ or 20′ lengths and you cut it to the length you need.

Install rebar in 2′ or 3′ grids and tie it together using zip ties or a wire twister tool and wire ties.

If you use rebar and have to cut it, you can rent a rebar cutter at HD or a local tool rental store. Or you can buy a good rebar cutter / bender on Amazon.

10 x 10 concrete slab

After the wire mesh goes in, you’re ready to pour the concrete. If you’re using ready-mix concrete, choose a nice, dry day and call your local concrete supplier to schedule the pour.

Most likely you’ll have to give them about a weeks notice so don’t wait till the last minute to call.

If you’re using bags of concrete, use my concrete yardage calculator to see how many bags you’ll need.

Learn how to mix concrete by hand here.

step 6. how to pour the concrete

how to pour concrete for a slab

When the concrete arrives, ask the mixer driver for for a 6 inch slump. Slump is how dry or wet the concrete is mixed. A 6 slump is a good workable mix to pour with.

Start pulling the concrete around and filling in the forms. Pull up the wire mesh or rebar into the concrete as you pour. (or you can put small pieces of brick under it to hold it up)

Pour out as much as you’re comfortable with (maybe about half on something like this if you’re a beginner) before you screed it level.

how to pour concrete

If you’re mixing bagged concrete for your slab, it’s the same process. Just slower.

Mix enough concrete until you have enough of the forms filled to screed the concrete.

I like to use ready mix myself. It’s just faster and more convenient for me since we do multiple pours like this in a day. Either way is good. Ready mix will be more expensive on a smaller slab vs bag mix.

See how many bags of concrete come on a pallet and what they cost.

how to pour concrete

Screed the concrete level using a magnesium screed board like us or a straight 2 x 4. Use short pulling strokes and tip the screed slightly on the back edge.

Put pressure down on the screed as you pull it to make sure it rides on top of the forms. Let your helpers push concrete (to fill low spots) and pull concrete back (if it’s high) as you screed.

The concrete rakes (kumalongs) we use make moving the concrete around a lot easier.

how to bull float concrete

After you screed the concrete, use a bull float to smooth the surface.

A bull float pushes down the aggregate on the surface and brings up some cement paste (creme).

Tip up the front edge and slowly push it from one side to the other. When you reach the opposite side, stop, tip up the back edge and slowly pull it back to you.

It might take multiple passes in the same spot to get it nice and smooth (usually 1 – 3 times).

After you’ve done the entire slab this way, you’re almost done with the pour.

step 7. installing anchor bolts in concrete (optional)

how to install anchor bolts in a slab

If you’re using anchor bolts, now is the time to put them in the concrete. Measure out where you want them and make a mark in the concrete.

Push the anchor bolt into the concrete to the desired level you want. I usually leave about 2 inches sticking up out of the concrete.

PRO TIP: Once you push it into the concrete a few inches, slightly jiggle it up and down to consolidate the concrete around the bolt as you set it to your finished level.

Now you’re done pouring the concrete.

Learn how to pour and finish concrete in my private training academy The Concrete Underground.

watch and i’ll show you how to pour a concrete slab

If you’re thinking of doing a broom finish, smooth trowel finish, or a textured finish on the concrete, I can show you how to finish the concrete HERE.

Another very important step is to “cure” the concrete. Click on CONCRETE SEALER to learn about this.

You can remove the forms the next day. 


Return from How To Pour Concrete to Concrete Slab

Return from How To Pour Concrete To Everything About Concrete Home Page


If you liked this, please share.  Thanks!




Source: https://www.everything-about-concrete.com/how-to-pour-concrete.html

Continue Reading

Concrete

Jan 2, How To Mix Concrete – The Most In Depth Guide On The Internet

Learn how to mix concrete by hand using a wheelbarrow, concrete mixing machine, bucket or a tub. Detailed instructions and a video shows you how mix concrete.

Republished by Plato

Published

on

diy how to mix concrete at home

I’ll teach you my method of how to mix concrete: to get the proper firmness, texture, and strength.

tools you need for mixing concrete

Warning: Always wear safety gloves, safety goggles, and a dust mask when working with concrete.

Materials used for mixing concrete

  1. Concrete bag mix
  2. Water
  3. Portland cement – sand – gravel – optional if you’re mixing concrete from scratch.

Video: shows you how mix concrete by hand using quikrete

Owner Mike Day of Day’s Concrete Floors shows you how to properly mix concrete to repair a broken section of pool deck.

step by step: how to mix concrete

step 1. set up your mixing area

If you’re mixing multiple bags of concrete it’s a lot easier and faster if you have your mixing area organized.

If you’re only mixing one or two bags (like in the video) then all you need is your bag(s) of concrete, wheelbarrow, water, hoe.

On bigger projects it’s important to get all your bags in order and have plenty of water on hand. Having 2 people mixing and one spreading and smoothing the concrete makes the work go a lot faster.

How to mix concrete

step 2. measure the proper amount of water

I like to pre-measure the amount of water needed per bag and add it to the wheelbarrow first. 

I feel putting the water in first, then adding the dry concrete ingredients, makes the mixing process easier and faster.

how much mixing water to mix concrete

The water table below shows you how much water to use per bag. 

Depending on the bag size, there’s a range of water you can add for mixing.

For and 80 lb. bag of Quikrete, you can use 6 pints to 9 pints (3 – 4.5 quarts) of water to mix each bag.

I like to add the minimum amount to the wheelbarrow first, then add more water up to the maximum if I feel it needs it to get a good workable mixture.

If you use more water than the maximum amount recommended, then your concrete mix will not be as strong as advertised on the bag. 

mixing water for Quikrete

step 3. add the bag mix to your wheelbarrow (tub, bucket, or mixer)

how to mix Quikrete

Add about 1/2 to 2/3’s of the bag mix into the wheelbarrow. Mix that amount with the water until all the dry ingredients are saturated. 

Add the rest of the bag and keep mixing. Use this same technique if you’re mixing in a bucket or a tub.

If you’re mixing in an electric concrete mixer machine, then you can add the whole bag at one time.

how to mix bags of concreteMix half to two-thirds of the bag first then add the rest

step 4. mix the concrete to a workable consistency

Add the remainder of the bag and continue to mix the concrete. Move the hoe back and forth completely mixing the dry concrete mix with the water.

how to mix concrete by handToo dry – add more water and keep mixing

Add more water (up to the maximum amount) until you get your desired consistency.

Your concrete mix should look similar to the concrete below when it’s mixed properly.

It took me about 3 minutes to measure and add the water, then mix the 1 bag of concrete to this texture. 

Be careful not to get the mix too wet or it’s more likely to crack and won’t be as strong.

If you feel the concrete mix is too runny (wet) just add some more concrete mix from another bag until you feel it looks like the picture below.

PRO TIP: Always have an extra bag of concrete on hand just in case your project takes more concrete than you expected it to.

how to mix concrete in a wheelbarrowThis is what a good workable consistency looks like

step 5. place the mixed concrete where you need it

A good thing about mixing concrete in a wheelbarrow is you can wheel the concrete right where you need it.

Dump the concrete out of the wheelbarrow or shovel it out, like I’m doing on this job.

how to mix concrete

One way you can tell if you mixed the concrete properly is if you can move the concrete in place using a mag float and float it smooth going back and forth over it a few times.

how to mix concrete by hand

step 6. clean the concrete off your tools as soon as possible

Clean the wheelbarrow, hoe, and shovel with water as soon as you finish. The concrete mix will dry on them very quickly. 

PRO TIP: If the concrete mixture dries on your tools, use a margin trowel to scrape it off first, then rinse and scrub with water.

If you have a water hose and a stiff bristle brush nearby, rinse off the bulk of the concrete first, scrub the remaining cement paste, and rinse clean.

Do this in an area you don’t have to clean up the washed off concrete afterwards. Never wash off concrete onto your driveway or garage floor, it could permanently stain it.





how to mix concrete in a bucket

how to mix concrete with a drill

When I mix concrete in a  bucket, I like to have an over-sized bucket like this 18 gallon bucket in the picture. (best place to buy this is on Amazon)

I also like to use a mixing drill to mix my bags of concrete. A mixing drill like this one makes the mixing process very fast and is really the only way to mix concrete using a bucket.

The mixing process is the same as above: Add your water first, add 1/2 bag and mix, add remainder of bag and mix, add water up to the max. amount if needed. 

how to mix concrete in a mixer

If you’re using an electric concrete mixer machine it’ll speed up the mixing process because you can mix 2 – 3 bags of concrete at one time. (depending on the size of your mixer)

How to mix concrete in a mixer

The Mixing Process Goes Like This:

  1. Pre-measure your water and add it to the mixer first.
  2. Turn on the mixer before you add the first bag of concrete
  3. Add the first bag and let it mix for a minute (2 minutes if you’re only mixing one bag)
  4. Add the second bag and continue to mix for 2 – 3 minutes
  5. If the mix looks too dry add a little water as it’s mixing (only add water up to the max. amount)
how to mix concrete in an electric mixer

When the concrete looks mixed to the right consistency, dump it out of the mixer and into a wheelbarrow.

You can buy a really good portable electric concrete mixer machine on Amazon for $200 to $300 dollars.

what is the ratio for mixing concrete?

How do you mix your own concrete? 

If you’re using Portland cement, sand, and gravel to make your own concrete, you can use the 1-2-3 mixing ratio.

This concrete mixing ratio is done by mixing 1 shovel of cement with 2 shovels of sand and 3 shovels of gravel. (or some other accurate way to measure your ingredients)

Add the dry ingredients into a wheelbarrow or the electric mixer before you start adding water.

When you add more dry material to the mix, keep the 1:2:3 ratio of cement to sand to gravel the same for consistency and strength.

The amount of water you add to the mix will be based on how the mix feels while you’re mixing it. Use the wheelbarrow method above to judge how the final mix should look.

For more examples of proper concrete mix proportions check out my concrete mixing ratios for mixing concrete from cement, sand, gravel, and water. 

Learn how many bags of concrete it takes to make a cubic yard.

what’s the best type of concrete mix to use for:

1. Best concrete mix for a driveway is:

2. Best concrete mix for concrete countertops

3. Best concrete mix for fence posts

4. Best concrete mix for a patio

5. Best concrete mix for sidewalks

6. Best concrete mix for footings

7. Best concrete mix for slabs

Quikrete 5000 or Quikrete Crack Resistant Mix

Quikrete 5000 (add 2 cups cement)

Quikrete Regular or Fast Setting Mix

Quikrete Crack Resistant Mix

Quikrete Crack Resistant Mix

Quikrete Regular Mix

Quikrete 5000, Crack Resistant, or Regular

This list is my opinion only based off my experience using Quikrete Concrete mixes for my jobs.

Sometimes I’ll mix 1/2 a bag of Quikrete 5000 with one of the other bag mixes because it has a higher ratio of cement in it. This makes the overall mixture a little easier to finish.


Go from How to mix concrete to Concrete Slab

Go to Home Page


If you liked this, please share.  Thanks!




Source: https://www.everything-about-concrete.com/how-to-mix-concrete.html

Continue Reading
News5 days ago

Pure Harvest Bolsters Corporate Team with Key Additions

Uncategorized3 days ago

MediPharm Labs Appoints Warren Everitt, CEO Australia Pacific, to Board of Directors

Heartland5 days ago

High Times Greats: John Carpenter

Uncategorized2 days ago

New York Small Business Cooperative License

Uncategorized4 days ago

Truss CBD USA Is Hexo’s Official Entry Point Into The U.S. Market

Heartland4 days ago

MindMed Adds Chief Development Officer with FDA Phase 2 Psilocybin Clinical Trial Experience

Heartland4 days ago

Argentina Allows Cannabis Self-Cultivation

Heartland5 days ago

Vext Science Raises C$18 Million Selling Units at C$1.12

Uncategorized2 days ago

New York Cannabis Distributor License

Heartland2 days ago

30 Best Stoner Coloring Books on Amazon

CBD5 days ago

3 Major European Cannabis Markets That Could Boom In 2021

CBD5 days ago

Truss CBD USA, a Molson Coors and HEXO Corp Joint Venture, Launches Veryvell™ Sparkling CBD Water in Colorado

News5 days ago

Indiva Provides Guidance of Record Net Revenue for Fiscal Q4 2020

Heartland5 days ago

Executive Spotlight: Paola Fernandez

Uncategorized3 days ago

Cannabis Sector Reverse Splits – The Good, The Bad, and The Ugly

Heartland3 days ago

Mama Cultiva & the Fight for Cannabis Legalization

Uncategorized2 days ago

New York Cannabis Delivery License

CBD18 hours ago

What are Some Major Factors to Keep in Mind When Buying CBD Vape Oil?

News5 days ago

Planet 13 Holdings Inc. Announces Upsize to Bought Deal Public Offering

CBD4 days ago

CBD Vaporizer Battle: Refillable vs. Disposable

Hemp3 days ago

The USDA Has Released Its Final Rule on Hemp Regulation

Uncategorized2 days ago

Cannabis Nursery in New York

CBD4 days ago

Terpenes Deconstructed

News5 days ago

Vext Announces $15 Million Bought Deal Public Offering

CBD4 days ago

A Guide to the Latest Skincare Trend: Hemp Lotion

Heartland4 days ago

New Year, Same You

CBD4 days ago

CBD News: 2021: The year of positive CBD policy changes

CBD4 days ago

“From Distilling to Fulfilling”: Christina Lake Cannabis Produces First Ultra-High Potency Distillates and Commences Marketing to CPG Industry

Heartland19 hours ago

Investors in This Cannabis Stock Are Leaving $800 Million on the Table

Heartland4 days ago

Could the paper industry turn the page on trees in favor of a more sustainable fiber?

Trending

A Cloud Nine Capital Entity Copyright © 2020 – All Rights Reserved Proudly Made in America