Connect with us

Concrete

Coronavirus: Ritchie Bros registers record numbers and bidders

In the wake of coronavirus, Ritchie Bros has announced record bidder registrations from its restricted

Republished by Plato

Published

on

In the wake of coronavirus, Ritchie Bros has announced record bidder registrations from its restricted and online-only events.

Ann Fandozzi, Chief Executive Officer, Ritchie Bros, says: “Right now, we are limiting or eliminating onsite attendance in accordance with local restrictions and promoting online participation. This week in Columbus, OH, we held an online-only event with a live auctioneer; in France we held our auction strictly through our Timed Auction system; and in Sacramento, in accordance with local authorities, we allowed a limited number of onsite bidders, while the majority participated online. For every one of these events we saw a record number of bidders. We are also selling thousands of items every week through our online marketplaces IronPlanet, GovPlanet, and Marketplace-E.”

Columbus, Ohio – 17 – 18 March

A record 5,800+ people from 51 countries registered to bid on the 2,400+ items sold in Ritchie Bros.’ Columbus, Ohio auction. Leading up to the sale, web traffic was at a record high—up 45% from the same auction in 2019. Approximately 60% of the items sold in the auction were sold to buyers from Poland, Singapore, and the United Arab Emirates. Sales highlights in the two-day auction included a 2015 Caterpillar D6T XL crawler tractor that sold for US$220,000 and a 2019 Volvo VNL64T670 sleeper truck tractor that sold for US$91,000.

Jim Prince, Owner of Prince Pipeline Integrity, says: “I’ll admit, I was a little worried about the Columbus auction changing to online-only, but true to form, Ritchie Bros. exceeded my expectations and the results for my items were great. Thank you, Ritchie Bros. for caring about the safety your customers while continuing to do what you do best.”

St. Aubin sur Gaillon 17 – 18 March

A record 1,900+ people from 76 countries registered to bid on the 2,600+ items sold in Ritchie Bros.’ auction in St. Aubin sur Gaillon, France. Approximately 60% of the assets were sold to buyers from Australia, Vietnam, and the United States. Sales highlights included a 2016 Caterpillar 320EL hydraulic excavator for €83,000 (US$92,694) and a 2013 Manitou MRT2150 Plus 4x4x4 telescopic forklift that sold for €80,000 (US$89,344).

Sacramento, California – 18 March 2020

More than 6,400 people from 54 countries registered for Ritchie Bros.’ auction in Sacramento, CA this week—25% more bidders than the same auction last year and a record high for the site. Approximately 64% of the equipment in the auction was sold to buyers from California. Sales highlights in the auction included a 2015 Caterpillar D6N LGP dozer that sold for US$142,500 and a 2017 John Deere 160G LC hydraulic excavator that sold for US$125,000.

Ritchie Bros. has more than 60,000 items scheduled to sell its upcoming live and online events. For more information about upcoming events is available here.

Source

(Visited 1 times, 1 visits today)

Source: https://www.aggregateresearch.com/news/coronavirus-ritchie-bros-registers-record-numbers-and-bidders/

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.



how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.





how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.





how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading
CBD5 days ago

CBD News: CBD court ruling brings additional support in Germany for access

Material2 days ago

Improved sinter-bonding properties of silver-coated copper flake paste in air by the addition of sub-micrometer silver-coated copper particles

Heartland4 days ago

Everything You Need to Know About the Miraculous Health Benefits of Cannabidiol

CBD4 days ago

GreenheartCBD Founder Paul Walsh named to the All-Ireland Business All Star List

Material3 days ago

Colorful and antibacterial nylon fabric via in-situ biosynthesis of chitosan mediated nanosilver

Heartland19 hours ago

High CBD/low THC content for a new user?

Material3 days ago

Synthesis of Silica-based Scaffolds with High Porosity and Controllable Microstructure by a Sintering-free Sol-gel/Freeze-casting Hybrid Method under Mild Conditions

Heartland2 days ago

What happens when you green out?

Material4 days ago

A comparative study of hot ductility of unadded and Ce-added SA508-4N RPV steels

Heartland2 days ago

Model Katiana Kay Launches Bay Smokes

CBD5 days ago

The 20 Strongest CBD Oil Products Available

Heartland5 days ago

Cannabidiol Derivative May Be Effective as EB Treatment, Studies Suggest

Heartland2 days ago

Anyone try kokonuggz with THC?

Manufacturing4 days ago

Rubber-Metal Bonding

News4 days ago

Will Donald Trump gratify cannabis prisoners before leaving the White House?

Heartland3 days ago

How Does Heat Not Burn Work?

Concrete3 days ago

Nov 27, DIY Epoxy Concrete Crack Repair – What I use – How I Repair Concrete

Material3 days ago

First-principle computations of ferromagnetic HgCr2Z4 (Z=S, Se) spinels for spintronic and energy storage system applications

Heartland1 day ago

lol

Heartland19 hours ago

CBD oil brain fog

Heartland5 days ago

Tried baking brownies with CBD?

Heartland5 days ago

Heartland2 days ago

Heartland2 days ago

Heartland1 day ago

LASG destroys 1700 illegal shanties, recovers illegal substances at Agege

Heartland5 days ago

A Screenless, LED Display CBD Battery—The DOT Vaporizer

Heartland5 days ago

Mother, son, uncle arrested with 49 parcels of hemp in Kano

Heartland5 days ago

Charlotte's Web CBD products review: What to know

Uncategorized5 days ago

The Grinch Cocktail With Cannabis-Infused Rum

Material5 days ago

Microstructure and corrosion properties of Single Layer Inconel 625 Weld Cladding Obtained by the Electroslag Welding Process

Trending

A Cloud Nine Capital Entity Copyright © 2020 – All Rights Reserved Proudly Made in America