Connect with us

Concrete

Caterpillar VP Phil Kelliher will chair the CONEXPO-CON/AGG 2023 exhibition

The Association of Equipment Manufacturers (AEM) has chosen Caterpillar’s vice president Phil Kelliher to chair

Republished by Plato

Published

on

The Association of Equipment Manufacturers (AEM) has chosen Caterpillar’s vice president Phil Kelliher to chair CONEXPO-CON/AGG 2023 in Las Vegas.

The AEM says Kelliher is to lead a cross-section of construction equipment leaders to oversee planning of the triannual global gathering place of the construction industry.

Dana Wuesthoff, CONEXPO-CON/AGG show director, says: “His vast international experience and progressively responsible roles at Caterpillar will play a key factor in continuing to push the ROI discussions for exhibitors within the show management committee.

“We know he will ably guide the show’s strategic direction to deliver an enhanced experience at CONEXPO-CON/AGG 2023.”

In his role at Caterpillar, Kelliher is responsible for Americas distribution, service & marketing, providing governance and administration of Cat dealers in North America and Latin America.

Since joining Caterpillar in 1994 in Australia, he has held numerous marketing and managerial positions in the agriculture, construction and mining industries with multiple international assignments in Australia, Chile and the US.

The next CONEXPO-CON/AGG will take place at the Las Vegas Convention Center from 14-18 March 2023.

(Visited 1 times, 1 visits today)

Source: https://www.aggregateresearch.com/news/caterpillar-vp-phil-kelliher-will-chair-the-conexpo-con-agg-2023-exhibition/

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.



how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.





how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading

Concrete

Nov 27, How To Pour A Garage Floor In 17 Minutes! (Learn My Fast Method)

I’ll show you my method for pouring a garage floor in 17 minutes. Pouring concrete floors fast takes certain steps and planning for a successful pour.

Republished by Plato

Published

on

The process I use for pouring a concrete floor for a garage is:

  1. Order the concrete from a ready mix concrete company
  2. Establish concrete floor grade using a laser level 
  3. Mark grade level on the walls and snap chalk lines for perimeter grades
  4. When concrete truck shows up, mix the concrete to a workable slump
  5. Start pouring out the concrete as close to your grade lines as possible (pour a section at a time)
  6. Use laser level to set concrete floor grade in the middle of the garage (a wet pad)
  7. Mag float the concrete, matching your chalk lines around the perimeter
  8. Start leveling the concrete with a screed using your mag floated pads
  9. After screeding level, use the bull float to smooth the surface
  10. Repeat for each section until you’re done pouring the garage floor

The time it takes you to pour your garage floor will vary depending on your experience level and how big or small your garage floor is.

watch us pour this garage floor in 17 minutes

The size of the garage floor we’re pouring in the video is 24′ x 24′. I was hired to just pour and finish the floor.

I wasn’t hired to prep the gravel or install poly vapor barrier or install reinforcement. That stuff was the responsibility of the General Contractor. 

We used 4000 psi concrete with fiber mesh (reinforcement) and the concrete had a water reducer in it. The water reducer is a chemical they add to the concrete that allows you to pour a looser mix without adding water. 

How thick does a garage floor need to be?

That depends on what you’re using the garage for. Most residential garage floors like this one are 4″ thick.

As long as the sub-base has very good compaction, a 4″ thick floor is good enough for most cars and light duty trucks.

For heavier vehicles, a 6″ thick garage floor would be better for supporting bigger trucks and commercial vehicles.





how do you prepare the ground for a concrete floor in a garage?

The best way to prepare the sub-base for a garage floor is to use gravel. Remove any sod, loom, clay, or dirt that’s not gravel.

Install 2″ minus gravel for the lower sub-grade and compact it in 8″ lifts. Once you get to within 6″ of the final sub-base grade, switch to a 3/4″ crushed gravel for the remaining 6″.

This smaller aggregate gravel is easy to rake and level off. Using a laser level to check your grade, rake, compact and level the gravel to your final grade.

How deep you have to go with the gravel will depend on where you live, your existing soil conditions, and your existing landscape.

If you live in an area with a lot of freeze/thaw conditions, you’ll use a deeper gravel base than if you live in the South USA. Check with your local code enforcement to see what works best in your area.

can you pour a garage floor in sections

Yes, you can pour a garage floor in sections. If you feel you can’t pour all the garage floor at one time then form it off in smaller sections.

Use 2×4’s or 2×6’s to form one section at a time and just pour that first. Strip the forms the next day and form up the next section.

I would drill holes into the previous section with a 1/2″ masonry bit and pin the sections together. Drill into the concrete about 3″ and about every 2′ on center. Use 1/2″ dowels or rebar about 12″ long for your pins.

Hammer them in just before you pour the new section. These pins will keep one section from moving higher or lower than the other one. They’ll help keep the joints nice and tight together as the concrete cures.

IN CONCLUSION:

You may not be able to pour your garage floor in 17 minutes, that’s really not important. The method we pour our garage floors will help give you an idea how to pour yours a little faster though.

To learn more about how to pour and finish concrete like we do, check out The Concrete Underground.

That’s my private training academy for helping teach people like you how to work with concrete.

Home Page


If you liked this, please share.  Thanks!





Source: https://www.everything-about-concrete.com/how-to-pour-a-garage-floor-in-17-minutes.html

Continue Reading
CBD3 days ago

CBD News: CBD court ruling brings additional support in Germany for access

Metal4 days ago

RINL subsidiary BSLC seeks to make dolomite supplies to other steel mills

Material6 hours ago

Improved sinter-bonding properties of silver-coated copper flake paste in air by the addition of sub-micrometer silver-coated copper particles

CBD3 days ago

GreenheartCBD Founder Paul Walsh named to the All-Ireland Business All Star List

Material4 days ago

Fabrication and characterization of nanostructured zinc oxide on printed microcontact electrode for piezoelectric applications

Material4 days ago

Gamma radiation modified the optical, electrical, and antibacterial characterization of CuONPs doped in Polyethylene Oxide/Polyvinyl Alcohol

Heartland4 days ago

REVIEW: High Five Duo

Manufacturing5 days ago

Building Fundamentals of Manufacturing

Heartland4 days ago

Plus Products Trims Losses As Revenues Rise

News4 days ago

CBDPure Coupon Code for 2020 Holiday’s

Heartland2 days ago

Everything You Need to Know About the Miraculous Health Benefits of Cannabidiol

News5 days ago

Maine’s First Month Of Legal Marijuana Sales Total $1.4M

Uncategorized4 days ago

Did Joe Biden and Kamala Harris Just Pull A Fast One On The Cannabis Industry?

Uncategorized4 days ago

Easy Cranberry Cannabis Pistachio Cheese Log

Heartland4 days ago

Pairing beer and weed: a match made in heaven

Heartland5 days ago

News4 days ago

AM Solutions unveils new technology and test centre

Heartland4 days ago

British Virgin Islands: Medical Cannabis Momentum Stalls

Heartland4 days ago

Subversive SPAC Forms The Parent Company With Jaz-Z, Roc Nation

Heartland4 days ago

Do I need to take CBD oil every day for Anxiety?

Heartland4 days ago

How to Protect Your Intellectual Property

Heartland4 days ago

Hemp Biomass Decarboxylation Service Market 2020 Share, Vendor Detail, Technologies …

Heartland4 days ago

3 Delta-8 THC Flowers You Must Try This Black Friday

Heartland5 days ago

Uncategorized4 days ago

Aleafia Health Launches Kin Slips® Rapid Onset Cannabis-Infused Sublingual Strips

Heartland4 days ago

The LA Green Wednesday Steals and Deals Guide 2020

Heartland4 days ago

Hemp Pain — Crop falling out of favor with growers

Heartland4 days ago

Global Hemp Seeds Market 2020 : Industry Analysis by Top Countries Data Definition, Size, Share …

Heartland3 days ago

Vireo Health Q3 Revenue Increases 11% Sequentially to $11.9 Million

Heartland5 days ago

Trending

A Cloud Nine Capital Entity Copyright © 2020 – All Rights Reserved Proudly Made in America